How to Lay a Laminate Floor Tips for Laying Laminate Flooring

How to Lay a Laminate Floor Tips for Laying Laminate Flooring

How to Lay Laminate Flooring

Laminate flooring has come a long way since its humble beginnings and it is now a widely used flooring option, not only because of its low cost, but also the aesthetic and durability aspects too. Gone are the days of having to fork out for full price wood or slate floors, you can now get laminate alternatives that look practically identical to their counterparts, but at a mere fraction of the cost. So whether you are thinking about laying laminate flooring in just your bathroom. kitchen or entire house, then this is the guide for you!

Want to install Laminate flooring? Get free quotes from quality tradespeople

Tools You Will Need

Before you go and purchase the laminate flooring, you will need to work out how much of it you will require. You can do this by multiplying the length and breadth and then add an extra 10 – 15%. Once you have worked out how much laminate flooring you will require, it is time to go and buy it plus assemble all the tools needed to lay laminate flooring:

  • Laminate floor packs
  • Adhesive 
  • Underlay
  • Knife
  • Drill
  • Saw
  • Tape measure
  • How to Lay a Laminate Floor Tips for Laying Laminate Flooring
  • Spacers
  • Fitting tool 
  • Edging block
  • Hammer
  • Try square
  • Panel pins
  • Quadrant moulding

How much does it cost?

It depends entirely on how large the room is that you wish to lay laminate flooring in, as well as the quality and design of the actual laminate flooring itself. Prices start at around £20 per square metre. For a quote more specific to your needs visit a hardware store and investigate the different options available.

How to lay a laminate floor

Learning how to lay laminate flooring is not particularly hard, however if you lack the tools or the confidence it might be best to hire a laminate flooring fitter. Most jobs can be done in one or two days with minimal disruption, plus experts do this as their job day in day out so the finish would like be more professional than a DIY-er.

However, it you are keep to give it a go and lay your own laminate flooring and want to know how to lay laminate flooring in a hallway, kitchen, bedroom or any room in your house, then this step by step guide will come in handy.

Underlay

First things first you will need to take off any doors that open inwards into the room, this will make the job a lot easier. Remember to remove your shoes when doing this job, this will avoid any debris from your shoes imprinting the surface. It is important that you vacuum the entire room to remove any dirt too. You can then fit either underlay boards or a purpose-made sheet underlay. If you are wondering how to lay laminate flooring on concrete or floorboards, then this step is vital. The underlay will dampen the noise and give the boards a softer feel. With regards to concrete you should ensure that you use a damp proof membrane too, though this usually comes with most packs of laminate flooring.

Lay

Use your plastic spacers to create 60cm intervals along the largest wall, and then lay the first row of laminate boards, ensuring that the grooved side is facing the wall. You should make sure that the plastic spacers are far enough spaced apart to form the recommended expansion gap all around the edge of the floor. The ends of each of the boards will be tounged and grooved, you can join them up by applying glue along the top of the tongue and groove. If you are wondering how to lay click laminate flooring then it is exactly the same, except you will not need glue, instead they will click in to place. As you reach the end of the row you might need to cut the last board down to size. You can use your saw to do this.

Don’t discard the cut off board; instead starts the next row with it. Make sure you that your stagger the end joints of adjacent rows, a minimum of 30cm is usually recommended. To ensure a snug fit, use the fitting tool to push the ends of boards together whilst you are laying the laminate flooring.

Pipes

If you have to work around central heating pipes you can make holes by marking the position of the pipe on the board. You must then drill a small hole that is slightly larger than the pipe. Use your saw to make two angled saw cuts from the edge of the board to the sides of the drilled hole. You can then get the board, and very carefully use glue to fix the sawn off piece of laminate behind the pipe. Make sure that there is sufficient enough expansion gap around the entire pipe.

Finish

You can now either replace the skirting board on top of the new laminate flooring, or use a decorative quadrant moulding over the expansion gap between the laminate flooring at the wall. If you do the latter make sure you pin it to the skirting board then fit a new threshold over the edge of the flooring at the door.


Leave a Reply