Deeconstructed How to Prepare Vinyl Floor for Ceramic Tile

deeconstructed How to Prepare Vinyl Floor for Ceramic Tile

Prep for Tile Flooring

Once upon a time there was an ugly linoleum floor.

Long, long ago in a bathroom far away

Hickory dickory door,

I hate my linoleum floor.

Backer board down,

Trowel around,

Crap vinyl Ill see no more.

I might have sniffed a bit too much pipe dope working on the leaky sink. Or maybe Ive spent too much time confined to this 10 x 10 space. Im starting to lose my mind. Good thing my sense of humor is in tact.

Continuing my pursuit of a Property Virgin Approved master bathroom, I got to work prepping the existing sheet vinyl with cement board. I searched around the web to see what the pros said about installation. Some said you could just screw it down. Others insisted you must trowel on the mortar before securing with special cement coated screws .

Not a single one suggested cutting the 5 long sheets in half. I suppose they didnt expect it to be a 51 chick lugging the pieces across the room.

I bet the folks over at Pampered Chef dont expect their whisks to be used to mix up mud either.

But I find it works smashingly for the task.

I installed 1/4 green board  over mortar with screws set every 6 (roughly). I started off cutting the sheets with a drywall saw but quickly traded that out for a utility knife. It was much easier to score and snap the backer board. The saw kicked up way too much dust and was difficult to use.

Also up for internet debate was the use of mesh tape over the seams. Homes settle and since ours is 10 years old, its safe to assume its still getting situated. The back wall (where the toilet sits) is an exterior wall and I know the builders didnt over-insulate so, I went ahead and forked over the extra cash for piece of mind.

Before installing the backer board in the second half of the bathroom, I had to finish some residual demolition. Since I left the door jambs in place at the entrance and linen closet doors I had to use my new toy.

When Sonne was here last summer she cleaned up the trim in my office. Turns out an oscillating tool is perfect for carving out just enough wood to slip a ceramic tile in place. This trick saved me the hassle of removing/reinstalling the door jamb and stop.

How to Cut Door Frames without Removal

1. Set the backer board and tile against the door jamb and trace the top of the tile.

2. Cut the wood along the line with the oscillating tool. (Make sure youre wearing eye protection and dont cut too deep that youre compromising the wall studs.)

3. Double check that the tile fits snugly. Recut as necessary.

I skim-coated the entire floor to level and cover all of the exposed screw heads.

Note: Dont skimp and use regular screws to secure your underlayment. They will rust and compromise the overall substructure of your tile installation.

deeconstructed How to Prepare Vinyl Floor for Ceramic Tile

I let the floor dry completely before moving on to the next step.

Ceramic Yoga: Finding Center

I spent quite a while trying to figure out where to start the tile. When youre working in a large, square room its simple. Youd measure east to west and then north to south marking the intersection point. That would ensure most of the visual surface area was covered with full-sized tiles.

But what do you do when your room is cut in half by a wall and pocket door?

I chucked the professional advice and decided to wing it.

Since I was working with smaller tiles I went ahead and laid them out to get a feel for the finished space. I was able to manipulate the design pattern (grab tiles from different boxes to mix up the color/grain) and see just how much cutting I was going to need to do.

All the measuring and calculations in the world wont provide the same result as a dry run.

As I worked my way from the water closet to the vanity area I noticed the tiles starting to tip. Sure enough, there was a 1/4 discrepancy between the walls. Since I wasnt interested in reframing and hanging drywall, I opted to tweak a row of tiles to compensate.

Its a creative fix that youd only notice if you were on your hands and knees on the floor. Even then youd need tools to know for sure.

and a solid excuse for being in that position to begin with.

dee

This post is part of a series. Read the other parts here:


Leave a Reply