Resilient Tile VCT Hard Floor Care

Resilient Tile VCT Hard Floor Care

Resilient VCT Floor Care

Stripping a Resilient Tile Floor:

  1. Assemble the required products, equipment, and safety materials.
  2. Walk through area noting problem spots (i.e. damaged floors, gum, stickers, tar, etc.) Remove all sticky insoluble substances such as gum.
  3. Dust mop the floor to remove any loose soils, paper clips, sand, cigarette butts, etc.
  4. Strip the base boards and corners using High Power and a Swivel Power Scrub Brush .
  5. Strip floors, small areas at a time, by diluting one of the floor strippers according to label directions. Apply diluted product with a mop and let dwell for 5-10 minutes. (Do not let stripper dry or you will have to reapply.)
  6. When finish turns milky white, agitate the area using a low speed (175-300 rpm) rotary scrubber and a BLACK stripping pad .
  7. Pick up the stripper using a wet/dry vacuum or mop and bucket with clean water. Or pick up using an extractor with a squeegee floor tool .
  8. Flood rinse the area with cool, clean water.
  9. Pick up excess water with a wet/dry vacuum or an extractor with a squeegee floor tool l .
  10. A second rinse may be needed.
  11. Resilient Tile VCT Hard Floor Care
  12. Place caution signs around area until it is completely dry.

Building a Shine on a VCT Resilient Tile Floor:

  1. Check floor, making sure that it is totally dry and free of any old finish or stripper residue. If there is a whitish cast, this could indicate stripper or old finish still remains on the floor. If necessary, re-strip the floor.
  2. Floor temperature should be above 54 degrees F. for proper curing of finish.
  3. Select the proper floor finish.
  4. When applying finish, the single biggest problem that occurs is applying coats of floor finish before the previous coat has dried thoroughly.The applicator head will tear at the finish from its weight and the re-emulsify the coating. This dulls the finish and can create mop marks that are hard to buff out.
  5. Apply the proper number of coats of finish using the following procedures:
    1. Pour the finish (Hi-Shine or Tight Shine ) into a clean bucket equipped with a wringer. If a clean bucket is not available, use a liner in the bucket so that the finish does not become contaminated. Place a medium-size rayon mop, such as the Lint Free Mop. in the finish and let soak for 5-10 minutes. A cotton mop should never be used for applying finish because it will leave lint in the dried finish.
    2. Place the bottom half of the mop in the wringer and wring out the bottom half of the mop. Avoid excessive buildup of finish in low-traffic areas by not applying finish to within 12 inches of the walls until later coats.
    3. Apply the finish in an 8-10 foot area. Frame the area by using the wet mop to make a U around the two long sides and one short side of the area. Starting at the bottom, fill in the “U” using side-to-side figure 8 strokes. Flip the mop over halfway down the U and use the other side. Do not lift the mop head while applying finish.
    4. Usually, floor finish will dry in about 30 minutes. However, this is just a general rule.Third and fourth coats take longer to dry than first or second coats. Additionally, high humidity and temperature can greatly delay drying.
    5. Be sure to clean and dry the mop after use and only use it for application of finish.

Maintaining the Finish of a VCT Resilient Tile Floor:

  1. Proper maintenance can extend the strip and re-coat cycle by several months or up to a year!
  2. Dry mop daily to remove loose dirt and impediments.
  3. Mix 1-2 ounces of Neutral Floor Cleaner in a clean mop bucket. Either mop floor with solution or use in a rotary scrubber with a red pad. Let floor dry thoroughly.

Burnishing and Dry Buff a VCT Resilient Tile Floor:

Follow steps 1-3 above. Use the appropriate colored dry buffing pad to enhance the floor’s shine.

A floor should be burnished as often as necessary to return the floor to the appearance that the customer requires. Most high traffic areas are burnished each day. Before burnishing, the floor should be properly prepared: swept of all loose dirt, scrubbed or mopped. There should be an adequate number of coats of finish on the floor for burnishing to succeed.

Burnishing helps maintain the clean, glossy appearance while enhancing durability and slip resistance. Never burnish a dirty floor — this only leads to a dirty, shiny floor!

Scrub and Re-Coat:

Follow steps 1 and 2 above. Reapply 1 to 2 coats of Hi-Shine or Tight Shine following the label directions for buffing after the new finish is dry.

Pricing for Stripping, Sealing and Applying Floor Finish to Resilient and Vinyl Floors:

There is no standard charge or going rate for janitorial work and the going rate for stripping, waxing and maintaining resilient floors varies by region.

The charge for a complete strip and wax job can run from 17 cents to 30 cents per square foot in the United States. Much depends on what contractors charge in your area, if you provide all supplies or charge the materials to your customer, the condition of the floor, if you must move chairs, tables, cabinets, etc. and other variables.

For cleaning, spray buffing or burnishing a floor, the rates are usually about 1/2 the rate of a complete strip and wax.

VCT Resilient Tile Floor Maintenance Products and Additional Information:


Leave a Reply