Blog Flooring Supply Shop, Flooring and Floors Heating Supply Discount Warehouse

Blog Flooring Supply Shop, Flooring and Floors Heating Supply Discount Warehouse

Posts Tagged Glaze n Seal

Maintain Concrete Pavers and Brick

October 16th, 2011

How To Seal & Maintain Concrete Interlocking Pavers & Brick

The following information is based on product application reports and manufactures information and is provided in good faith to assist the consumer. READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING. PRE-TEST IN AN INCONSPICUOUS AREA PRIOR TO APPLICATION TO DETERMINE IF THE DESIRED RESULTS ARE ACHIEVED.

Low-Medium Sheen

Water-based Film-forming

Surface Preparation

Newly manufactured concrete pavers should cure 14 days or more before sealing. Follow paver manufacturer’s recommendations. Prior to the application of Glaze N Seals sealer products, surface must be thoroughly clean. Remove all dirt, oil, grease, paint, efflorescence and any previous sealers that may not be compatible with the new sealer. General cleaning may be done using Glaze ‘N Seal’s alkaline base Heavy Duty Cleaner . Mix the concentrated detergent according to label instruction depending on severity of surface soils. For Efflorescence stains or hard water deposits, use Glaze N Seals mild acidic cleaner Efflorescence Remover. Note…(When acid has been used for any reason, surface must be neutralized). For neutralizing, we recommend Glaze N Seals Neutralizing Rinse. Always read cleaning product instructions and cautions with any cleaner.

After tamping down joint sand and sweeping the sanded areas for new installations, be sure the sand is at least 1/8 inch below the surface of the pavers. Make sure all sand residue and fine powder is removed with broom & blower before application of any film forming sealers. Allow any moisture in or on the surface of the pavers to dry at least 24 hours. Allow 48 hours or more if temperatures are cool or a pressure washer has been used. For best results the sand should be dry to its full depth before sealing. It is always recommended to test the sealer of choice in a small area first. Always read product label and directions carefully before beginning to use any sealer products.

  • Apply Glaze ‘N Seal’s Paver Sealer & Joint Stabilizer to a clean dry surface using a compressed air hand pump garden-type sprayer. Apply a heavy saturating coat of sealer. Ensure that all joints are flooded to maximize sealer soaking into the dry sand. Immediately squeegee any excess product down into the sand joints using a large foam or rubber squeegee. Avoid puddling on the surface. An optional second thin coat may be applied to the surface of the pavers after two hours if desired to increase protection & gloss. Ideal surface temperatures should be above 55° and below 85°.
  • After final coat, allow sealer to dry 2 hrs before foot traffic. Limit heavy traffic. Keep vehicular traffic and moisture off for 72 hours while sealer cure

Maintenance & Other Sealer Options For Concrete Interlocking Pavers & Brick

  • Maintain your pavers with periodic cleaning of grease, dirt, loose soil and hard-water stains with Glaze N Seal’s (Heavy Duty Cleaner ). For stubborn grease spots use Heavy Duty Cleaner in a more concentrated formulation. Rinse surface well with water.
  • Reapply maintenance coats of sealer as needed. All Glaze N Seal sealers are re-coatable. Make sure surface is clean and dry at time of reapplication.

If Considering Other Glaze ‘N Seal Sealers For Concrete Interlocking Pavers & Brick, See Options Recommended From Chart Below

Slate A Great Flooring Option

Flooring is an integral part of the house, which can significantly affect its appearance. Hence, it is vital to select the right flooring option for your home, which can make it look more attractive and appealing. Among the various flooring options available, more and more people are opting for slate, for residential as well as commercial buildings. Owing to its versatility and aesthetic appeal, it is increasingly being used in interiors as well as exteriors. Not only is it a feasible flooring option, but is also a great option for the walls, ceilings and roofs.

Slate adds elegance and sophistication to an interior, which other flooring options cannot. This sturdy natural-stone flooring option is formed when minute particles of silt and clay bind under high pressure and temperature. Owing to this process, slate gets its monolithic and ultra-fine texture. It is generally gray in color, but can also have shades of blue or green on it. However, it is also available in other colors like purple, brown and white pink, among others. You can make use of slate’s different shades of color for creating unique designs for your flooring. Along with its diversity in colors, slate tiles are also found in varied shapes, thicknesses and finishes. You can combine these variable attributes to your advantage and come up with different flooring ideas for house.

In comparison to various other flooring options, slate is a more durable and long lasting material. Once installed, it can last for many years and you may not have to replace it with any other flooring; thus, proving cost advantage. Additionally, it also has low maintenance requirements, unlike some other flooring options such as hardwood flooring. Slate is also resistant to dirt, and requires regular mopping with mild detergent cleaning.

The fine molecular structure of slate renders several advantages over other flooring options. Along with being tough, it is also resistant to moisture, which guarantees firm footing and avoids slipping or gliding. Owing to this, slate is a great flooring option for high traffic areas, or areas that are exposed to water, like hallways, porches, kitchen and bathrooms. In addition, this anti-stain flooring option is also bacteria and allergen resistant, thereby reducing the risk of diseases. To top it all, slate is quite affordable as compared to most of the other available flooring options, like marble and granite.

Blog Flooring Supply Shop, Flooring and Floors Heating Supply Discount Warehouse

Due to the various advantages offered by it, slate proves to be a great flooring option that can enhance the appearance of any décor. However, an important thing which one should always keep in consideration is that the installation must be done in the right manner. If the installation is not done properly, flooring may be susceptible to breakage.

Since slate is a heavy natural stone, it needs to be installed correctly on a strong, solid subfloor instead of a flexible subfloor. Once properly installed, it will last for several years, without much maintenance requirements. Hence, if you are planning to install new flooring, you should opt for slate, which has become a preferred flooring choice of many people.

To seal use Slate Sealer by Glaze n Seal that offers unsurpassed low gloss protection for slate, quarry, tile, and other dense tile. This easy to apply, fast drying, non-yellowing acrylic provides a barrier against oil, water, based stains, acids, and efflorescence indoors and outdoors. With excellent UV and abrasion resistance.

You can follow any responses to this entry through the RSS 2.0 Feed. You can leave a response. or trackback from your own site.

Posts Tagged Glaze n Seal

Maintain Concrete Pavers and Brick

October 16th, 2011

How To Seal & Maintain Concrete Interlocking Pavers & Brick

The following information is based on product application reports and manufactures information and is provided in good faith to assist the consumer. READ ALL INSTRUCTIONS AND PRODUCT LABELS COMPLETELY BEFORE USING. PRE-TEST IN AN INCONSPICUOUS AREA PRIOR TO APPLICATION TO DETERMINE IF THE DESIRED RESULTS ARE ACHIEVED.

Low-Medium Sheen

Water-based Film-forming

Surface Preparation

Newly manufactured concrete pavers should cure 14 days or more before sealing. Follow paver manufacturer’s recommendations. Prior to the application of Glaze N Seals sealer products, surface must be thoroughly clean. Remove all dirt, oil, grease, paint, efflorescence and any previous sealers that may not be compatible with the new sealer. General cleaning may be done using Glaze ‘N Seal’s alkaline base Heavy Duty Cleaner . Mix the concentrated detergent according to label instruction depending on severity of surface soils. For Efflorescence stains or hard water deposits, use Glaze N Seals mild acidic cleaner Efflorescence Remover. Note…(When acid has been used for any reason, surface must be neutralized). For neutralizing, we recommend Glaze N Seals Neutralizing Rinse. Always read cleaning product instructions and cautions with any cleaner.

After tamping down joint sand and sweeping the sanded areas for new installations, be sure the sand is at least 1/8 inch below the surface of the pavers. Make sure all sand residue and fine powder is removed with broom & blower before application of any film forming sealers. Allow any moisture in or on the surface of the pavers to dry at least 24 hours. Allow 48 hours or more if temperatures are cool or a pressure washer has been used. For best results the sand should be dry to its full depth before sealing. It is always recommended to test the sealer of choice in a small area first. Always read product label and directions carefully before beginning to use any sealer products.

  • Apply Glaze ‘N Seal’s Paver Sealer & Joint Stabilizer to a clean dry surface using a compressed air hand pump garden-type sprayer. Apply a heavy saturating coat of sealer. Ensure that all joints are flooded to maximize sealer soaking into the dry sand. Immediately squeegee any excess product down into the sand joints using a large foam or rubber squeegee. Avoid puddling on the surface. An optional second thin coat may be applied to the surface of the pavers after two hours if desired to increase protection & gloss. Ideal surface temperatures should be above 55° and below 85°.
  • After final coat, allow sealer to dry 2 hrs before foot traffic. Limit heavy traffic. Keep vehicular traffic and moisture off for 72 hours while sealer cure

Maintenance & Other Sealer Options For Concrete Interlocking Pavers & Brick

  • Maintain your pavers with periodic cleaning of grease, dirt, loose soil and hard-water stains with Glaze N Seal’s (Heavy Duty Cleaner ). For stubborn grease spots use Heavy Duty Cleaner in a more concentrated formulation. Rinse surface well with water.
  • Reapply maintenance coats of sealer as needed. All Glaze N Seal sealers are re-coatable. Make sure surface is clean and dry at time of reapplication.

If Considering Other Glaze ‘N Seal Sealers For Concrete Interlocking Pavers & Brick, See Options Recommended From Chart Below


Leave a Reply