Insulating the floor of a Passivhaus on piers… VT Passive House

Insulating the floor of a Passivhaus on piers... VT Passive House

Insulating the floor of a Passivhaus on piers.

Ted — August 6, 2011

The Passivhaus Institut has a really cool book that covers various Passivhaus building techniques in excruciating detail, including sectional drawings and descriptions of materials. Andrea put it on her Christmas wish list the year before last, so I got her a copy. It has dozens of different foundation details for different sorts of building environments.

I recommend the book highly even if you don’t actually wind up building what’s in it, because the drawings are really helpful for understanding how to avoid thermal bridges, how to detail the airtight seals between floors, walls and ceiling, and also for ideas about what sort of material to use. I searched it carefully for details that would work for our foundation, but it didn’t cover the case we originally designed: a house on a frostwall foundation with no basement. It had some drawings that were very helpful for thinking about how to detail the foundation, and when Marc and Andrea and I were brainstorming about how to build the actual foundation, that detail was very helpful in figuring out what to do (although Marc might argue that it led to me being obsessed with details that weren’t all that important).

What the book does not cover at all, however, is how to do a floor when your house is on a pier foundation. Both Marc and Peter were a bit concerned about how that was going to work, but it went pretty well in the PHPP model. Normally in a slab foundation, you’d lay down a really thick layer of expanded polystyrene foam insulation (EPS). This would isolate the interior of the house from the ground. Typically the ground under the house will be warmer than ambient, though, so the EPS doesn’t have to do as much work as our floor has to do to keep the house warm.

So we are going with a fairly thick floor—11 7/8″ thick, with 4″ of polyisocyanurate rigid foam insulation. The floor joists will be I-joists, to minimize thermal bridging. The insulation between the floor joists will be dense-packed cellulose. One really nice thing about this is that the floor will have a lot less foam in it than a typical floor—only 4″, rather than the typical 8″ or more of styrofoam insulation below the slab that you’d see in a Passivhaus.

An additional complication is that normally to get a good air barrier on the slab of a Passivhaus, you’d have a polyethylene membrane under the slab. This would then connect to the wall air barrier with some kind of sticky tape or expanding foam tape. We don’t have that option with the floor box, because there’s no place to put the polyethylene membrane.

Insulating the floor of a Passivhaus on piers... VT Passive House

Instead, the bottom of the box will be sheathed with zip sheathing. Zip sheathing provides an excellent air barrier. The edges of each piece of zip sheathing will be taped together. Remember, this tape is on the bottom of the sheathing. The bottom of the sheathing will be resting on the LVL beam or on the pressure-treated sill plate. This means that the sheathing has to be taped before it’s nailed to the plate or to the beam.

In order to accomplish this, Eli’s team is going to build the floor box in sections, upside down. They are going to tape the seams on the bottom of each section before flipping that section. When the time comes to install the sections, they will (handwaving, Eli, help!) to seal the joins between the sections.

The joint between the floor-bottom sheathing and the outer wall sheathing will be sealed with a gasket or caulk, as shown below. I’m not sure what sort of gasket to use if we go that route. We’d talked about using iso-bloco tape to seal the edge, but that stuff is very expensive. Another option would be to use EPDM gaskets. I don’t know how much the EPDM gaskets cost—maybe they’re just as expensive—but I suspect they are cheaper. It may also be that caulk is a good option, although I’ve heard arguments to the contrary.

Leave a Reply