KILZ 1-PART EPOXY CONCRETE & GARAGE FLOOR PAINT

KILZ 1-PART EPOXY CONCRETE & GARAGE FLOOR PAINT

KILZ 1-PART EPOXY CONCRETE & GARAGE FLOOR PAINT

WHERE TO USE

Ideal for horizontal surfaces such as: garage floors, driveways, basements, porches and pool decks. Can be applied to interior or exterior surfaces such as:

  • Porous Concrete
  • Masonry
  • Stone
  • Stucco
  • Brick
  • New and Uncoated Concrete or Masonry Surfaces. New concrete must cure for a minimum of 30 days. For proper penetration and adhesion of topcoat, use KILZ Concrete Masonry Cleaner Etcher to clean and etch the surface. Follow all label instructions. Apply KILZ Concrete Masonry Bonding Primer to increase adhesion of topcoat to the surface. Follow all label instructions.
  • Painted, Stained or Sealed Concrete: Option 1 — To completely strip the entire surface, use a product such as KILZ Concrete Masonry Paint Stripper. Follow all label instructions.

Option 2 — To recoat over an existing coating, remove any loose or peeling paint and scuff sand the surface. Use KILZ Concrete Masonry Cleaner Degreaser to clean previously coated surfaces in sound condition. Use a product such as KILZ Concrete Masonry Cleaner Etcher to clean and etch any bare concrete area. Follow all label instructions.

  • Prime all bare concrete areas with KILZ Concrete Masonry Bonding Primer to increase adhesion of topcoat to the surface. Follow all label instructions.
    • DO NOT THIN. Intermix all cans of same product to ensure colour uniformity. Stir before applying.
    • Stir well before use. Do not dilute. Use with adequate ventilation.
    • Use product when air and surface temperatures are between 10-32°C.
    • Apply a thin, even coat using a 10 mm nap roller cover, pad applicator or a nylon/polyester brush at a spread rate of 37-46 m ² (400-500 sq. ft.) per 3.79 L on smooth surfaces and of 28-37 m ² (300-400 sq. ft.) per 3.79 L on rough surfaces.
    • Allow first coat to dry 24 hours before deciding if a second coat is necessary. For uniformity, apply a second coat (in a criss-cross direction).
    • DO NOT APPLY MORE THAN TWO COATS. An annual touch-up may be required in areas subject to tire traffic

    DRY TIME

    Dries to touch in 2 hours. Longer dry time required in cooler temperatures and in higher humidity. The floor may be subjected to light foot traffic after 24 hours. Allow 72 hours before subjecting surface to heavy foot traffic or repositioning furniture. Allow 7 days before subjecting to automotive tires. Premature heavy traffic will cause paint failure requiring spot recoating. If necessary, corrugated cardboard may be used underneath automobile tires after 72 hours. Wait at least 30 days before rinsing or cleaning. Use a mild detergent as needed. Abrasive cleaners and pressure-washers should be used carefully to avoid premature paint failure.

    CLEAN UP & DISPOSAL

    • Clean equipment and paint spatters with warm, soapy water. If spilled, contain material and remove with an inert absorbent. Dispose of contaminated absorbent, container and unused product in accordance with all current governmental regulations.
    • Do not dispose of this product down a drain. Please consider donating any unused product. For recycling or disposal information contact your local household refuse collection service.
    • Protect from freezing.
    • For best results, apply at temperatures between 10°F — 32° C. Temperatures above 32° C may affect the application such as drying too fast. Avoid painting in direct sun. NOTE: If the surface is hot to the touch it should be considered too hot to apply this coating.
    • Avoid heavy traffic for 24 hours.
    • DO NOT APPLY MORE THAN TWO COATS
    • Allow two weeks before washing or cleaning for full cure.
    • Shelf life under normal conditions is two years unopened.


    Leave a Reply