Flooring Free Shipping over $225 @

Flooring Free Shipping over $225 @

Flooring

The floors in dollhouses or room boxes can be real wood, carpet, tile, brick or paper. Flooring, no matter the type, enhances the interior of your dollhouse.

When you do not want the carpet permanently attached, use double sided carpet tape around the edge of the floor and lay the carpet on top. Press down to attach to the carpet tape. If you wish to enhance your dollhouse with the look of wood, then the following suggestions should prove helpful. Wood flooring make beautiful backgrounds for handcrafted needlework and braided rugs.

It is up to you whether you varnish before or after installing. It is important, when staining the wood flooring, to stain the flooring before installing. (See the Painting Section .) Since wallpaper is normally applied before installing the flooring, by staining first, you do not get stain on the wallpaper. The stain is thin and does tend to splatter.

  1. Sand any rough or unlevel areas in order to achieve an even flat surface.
  2. Make sure the surface to be covered is both clean and free of dust and dirt.
  3. A number of glues may be used to apply floor pieces: wood glue. Quick Grip or white glue. Note: if a white glue or other glue with a water base is used, you must lay a heavy object (book, etc.) on top of the flooring when laid. The water in the glue may tend to make the flooring expand and buckle.
  4. Apply glue to the surface of the floor and lay one section of flooring at a time, tightly butting one to the other until the entire surface is covered. When you are laying the floor, be very careful not to get any glue on the surface of the flooring, as the glue will act as a sealer and will not allow stain or varnish to penetrate.
  5. If you do happen to get glue on the surface of the flooring, wipe the glue away with a damp cloth before it is allowed to dry.
  1. Be extremely careful not to get any Quick Grip on the surface of the flooring, because it will not wipe away with a damp cloth and thus will mar the surface of the floor.
  2. Be sure that when you use Quick Grip, it is even and does not ooze through the cracks. Apply Quick Grip on the back of the flooring instead of on the surface of the floor.
  3. Apply the flooring, making sure that it is placed exactly where you want it to be. Then pull the flooring up lightly and place it back down. Press the flooring to the surface.
  4. Because it dries immediately, you do not need to place a weight on top of the flooring.

Due to changes in weather and humidity, the raw wood may expand or contract, resulting in small cracks in the wood. If this happens, a simple technique to make the surface smooth again is using a very fine sandpaper, and sanding with the grain of wood (each square would be sanded individually). The fine dust will fall in any crevices and the excess may be wiped away with a damp cloth. This step should be followed even if no, racks appear, because all raw wood needs sanding before the finish is applied.

You may finish the flooring with a stain, antique or varnish. (See the Paint section .) A varnish will seal the flooring and will resist any weather change. I always like to finish with one or wo coats of varnish (sanding between coats) in order to give the wood a fine finish.

Because Parquet Flooring is made up of small sections of wood, it is sometimes easier to make a brown paper pattern of the floor. Glue the parquet to the brown paper pattern with a good paper-to-wood adhesive. This allows you to match the parquet to the area to be covered, including the partial sections of parquet. Do this for all size floors when using parquet, as it allows you to design the floor before installing. Since the parquet is on a paper backing, you can now use a wallpaper mucilage to apply to the floor.

Note: Unusual shaped floors using parquet definitely require using a brown paper pattern of the floor.

  1. Apply the parquet to the pattern with a good paper-to-wood adhesive, matching the parquet to the edge and beyond.
  2. Turn the floor over and trim the overhangs with a straightedge guide and a utility knife or X-Acto knife. Be sure to work on a board or hard surface that the knife won’t damage.
  3. Sand trimmed flooring as instructed in prior directions (above).
  4. Finish the floor before you place it into the house, because you might not be able to reach sections of the floor once it is in place, due to the irregular shape of the floor.
  5. The floor may be installed in the room with the Quick Grip or the wallpaper mucilage. Press firmly in place until the adhesive holds.

Tile floors may be installed the same way as the sheet flooring or the parquet floors, except that no sanding or varnishing is needed. You may also use the pattern method.

For a more economical floor, various styles of paper flooring are available in miniature shops. Paper flooring may be applied with wallpaper mucilage. Finish this type of flooring with three coats of polyurethane varnish for a real wood look. You might wish to use a gloss finish here. Since the paper flooring is printed, it is very important that you use a polyurethane finish, as it will not smear the ink.


Leave a Reply